NEW ENQUIRIES

API 681 liquid ring compressors
, Oct. 2010
Enquiry from ECIS Group, Muggio, Italy

Transformer Oil Regeneration System for 30 to 150 m3/h
, Aug. 2010
Enquiry from Western Transformers - Kingdom of Saudi Arabia

Refurbished high vacuum pumps and components
, Aug. 2010
Enquiry from BELINGENERPROM - Minsk, Belarus

ELMO-G 2BH1 1HC27 Vacuum Pump
, Aug. 2010
Enquiry from Ahwaz Pipe Mills Co. - Ahwaz, Iran

Turbo-compressor or liquid ring vacuum pump system for 18.000 m3/hr at 1.6 bar
, Aug. 2010
Enquiry from Energopromservice CJSC, Moscow - Russia

ATEX vacuum pump 3-20 m3/hr at 150-300 mbar
, Aug. 2010
Enquiry from Schlumberger Oilfield UK Plc

Low Noise Vacuum Pumps for Small Consumer Products
, Aug. 2010
Enquiry from NineSigma, Inc., Cleveland, USA

spare parts for Siemens elmo-g vacuum blower
, Mar. 2010
Enquiry from NineSigma, Riyadh, Saudi Arabia

info request for HIBON Type AL 20
, Feb. 2010
Enquiry from ERGOKINISI, Thessaloniki, Greece

looking for a small vacuum pump for a pilot unit
, Feb. 2010
Enquiry from BELINGENERPROM - Minsk, Bellarussia

gebrauchte Vakuumbeschichtungsanlage für Folien
, Jan. 2010
Enquiry from Jorge MORENO - Dortmund, Germany

Ersatzteile für Brey TF 1 Verdichter / Vakuumpumpe
, Jan. 2010
Enquiry from V. Leinberger - Sachverständiger für Raumbegrünung, Nieder-Olm






API 681 liquid ring compressors

Oct. 2010

Dear Sir,

We have the pleasure to submit your kindly attention to request for quotation for

02 Liquid Ring Compressor API 681 (2 x100%)

in accordance with the attached specifications:   Data sheet,   PID.

(flow rate 850 lb/h, discharge pressure 25 psig)

Final destination : Saudi Arabia
Quotation is required as per attached RFQ for the liquid ring compressors and or for the whole system consisting of the compressors, the separator, the service liquid cooler.
Break down is required with quotation of bare compressor(s).
Compressor Vendor is required to fill the attached compressor data sheet with the data required.
Compressor vendor should provide, with their offer, the design and sizing and the quantitative definition of the duty of each equipment as per P&ID, i.e. the compressors, the down-stream gas-liquid separator, the recycled liquid cooler and the associated process circuits.
Compressor vendor design shall take into account both the feed stream to the compressors and the gas stream injected on the compressor's discharge line and compressor discharge pressure value definition .
The two cases of composition and flow rate of feed gas in the RFQ and the two cases of composition of injected gas are to be considered for design.
Also, the definition of flow rate and conditions (P,T, liquid fraction) of each of the involved streams in/out each equipment are required as well as the required quantity and conditions of the service liquid to be supplied to each compressor.
Looking forward to receive your best technical and commercial offer quote at the earliest,
I thank you in advance for your kind support and for your gentle collaboration.
Yours Faithfully,

Bogdan Camenita

P.S. Waiting for receiving your proposal, we kindly ask to include in it a deviation list. We kindly ask you to submit an offer with the nearest/similar solution or with an additional/alternative solution that can anyway meet the requirements of our request.
If your quotation will contain any deviations from our original request, we kindly ask you to explain the reason for the deviation; please include in your offer a motivation that proves, from a technical point of view, that the items offered can satisfy anyway our requirements without any trouble for our client.


ECISGROUP S.p.a. - www.ecisgroup.it
- Via Pavia, 21 - 20053 Muggio, Italy
Bogdan Camenita - Proposal Engineer, email: B.Camenita@ecisgroup.it, Tel. +39.039.2788.1, Fax. +39 0392781353



Transformer Oil Regeneration System for 30 to 150 m3/h

Aug. 2010

We are looking for a vacuum system for power transformer drying.
The volume vary from 30 to 150 m3, the ultimate vacuum to reach within 24 hours will be 0.02 mbar

The system includes a vacuum controller and the automatic valves (shutoff valves, vacuum breaker,..)

Please send us best offer with technical details of a complete vacuum system

WESTERN TRANSFORMERS - www.westerntransformers.com - Amir-Metabe, Jeddah 21382, Kingdom of Saudi Arabia
Rehan Akhtar, email: rehan@westerntransformers.com, Tel. 00966 2 647 444, Fax 00966 2 674 2873



Refurbished high vacuum pumps and components

Aug. 2010


Dear Partners,

We are interested to purchase the following equipment:

1) refurbished two-stage rotary vane vacuum pump, performance 16-20 liters per second (EDWARDS E1M80) 2 pcs

2) refurbished roots vacuum pump, performance 50-80 liters per second (EDWARDS EH-250) 2 pcs

3) refurbished turbomolecular pump, horizontal operating position, as a unit with controller, performance 2000-2200 liters per second (SHIMADZU 2003) 2 pcs

4) high-vacuum valve, vane, pneumatically operated, aluminum material, as a unit with limit switches, diameter to fit with the turbomolecular pump (Diameter 250mm ?) 2 pcs

5) angle vacuum valve, box material - aluminum, pneumatically operated, with limit switches: Diameter 63mm: 2pcs; Diameter 40mm: 2pcs

6) bellows (Diameter 40mm), 750mm long 2pcs

7) thermocouple vacuum sensor Pirany Active measuring range 100 000 Pa - 1x10-2 Pa 8pcs

8) inverted-magnetron vacuum sensor AIM-X Active series, measuring range 1x10-1 1x10^-7 Pa 3pcs

These positions we need with garantee.

If you have no these positions in stock, you can offer us any other refurbished pumps with the same technical features.

Karima Ahmedhanova

BELINGENERPROM - www.nasosy.by - Volgogradskaya, 220049 Minsk, Belarus
Karima Ahmedhanova, email: minsk_nasos@mail.ru, Tel. +375172807456, Fax +375172631350



ELMO-G 2BH1 1HC27 Vacuum Pump

Aug. 2010

Dear Sir /.Madam ( Sales Manager )


Please be advised , we need the following item


Pos. 1) - QTY 02   ELMO-G 2BH1 1HC27 Vacuum Pump
Siemens Motor 7.5 Kw , 2930 rpm , 50 Hz , 380 V , IP 54
Serial No. : ECO 10 1107 26 006 .

Please check the matter and let us know the result it .

We thanks you in advance for your efforts .

Best Regards

Ali Safaei

Ahwaz Pipe Mills Co.

Ahwaz Pipe Mills Co. - www.apm-ir.com - Karoon Industrial Area, P.O.Box. 61775-1800, Post Code 61766-4-1198, Ahwaz - Iran
Yulia Kamynina, email: a.safaei@apm-ir.com, +98 611 227 03 41, Fax +98 611 227 49 40



Turbo-compressor or liquid ring vacuum pump system for 18.000 m3/hr at 1.6 bar

Aug. 2010


Kindly ask you to consider our new inquiry (data-sheet, pdf attached). We're searching for equipment to replace an existent gas blower. It can be a liquid ring vacuum pump systen or a blower system.

Gas to be handled: N2 + CO2 + traces of SO2, S2O4
Suction capacity: 18.000 m³/h
Suction pressure: -1200 mm H2O
Discharge pressure: 1.6 bar

Waiting for your reply. Thank you.

Best regards,

Yulia Kamynina

Energopromservice CJSC - 105005, Russian Federation, Moscow, nab. Akademika Tupoleva, 15-5
Yulia Kamynina, email: yukamynina@zaoeps.ru, Tel./Fax: +7 (495) 926 25 41



ATEX vacuum pump 3-20 m3/hr at 150-300 mbar

Aug. 2010

Hello,

I am looking for a vacuum pump with the following characteristics:

- ATEX zone 2, or zone 1 preferably
- 3 to 20 m3/hr at atmospheric pressure depending on the application
- High reliability and low / simple maintenance
- Regulated input pressure, adjustable anywhere in the range between 150 and 300 mbar (or wider range)
- The gas to be evacuated is principally methane, but it also could contain ethane, CO2, Nitrogen, some H2S, and water vapor.


Thanks in advance for your help,
Regards,

Dominique Dion
Project Manager

Schlumberger Oilfield UK Plc - 8 The Quadrangle; Abbey Park Industrial Estate, Romsey SO51 9DL - UK
Dominique Dion, email: ddion@exchange.slb.com, Tel. +33 1 5881 6010, Cell +33 6 2227 0474



NineSigma Request - Low Noise Vacuum Pumps for Small Consumer Products

Aug. 2010

NineSigma, representing a Global Consumer Products Company, invites proposals for a desktop vacuum pump and control unit that are both cost-effective and quiet.

More information is available in the Request for Proposal (RFP #66555, pdf download)

The final submission date for Proposal Briefs is August 27, 2010.

REQUEST FOR PROPOSAL DESCRIPTION

NineSigma, representing a Global Consumer Products Company, invites proposals for a desktop vacuum pump and control unit that are both cost-effective and quiet.

Proposals that adapt existing technologies from military, medical, printing, automotive or other positive pressure/vacuum pump applications are highly desirable.

The successful technology will use either one or two pumps/unit to achieve the following functional specifications:
- Have cycle frequency higher than 1.7Hz (atmospheric to max. vacuum and back to atmospheric)
- Evacuate 70ml air/cycle/pump
- Achieve a max. vacuum of 300 mmHG
- Maintain maximum vacuum for 0.5 secs
- Exhibit no loud or harsh sounds (Max. noise: 52dBA)
- Be durable (more than 1100 hrs of repeated cycles)
- Include rechargable batteries capable of providing >3 hrs of vacuum pump use
- Include 110/240V transformer capable of recharging batteries in 1- 3 hrs.
- Able to achieve functional specifications at 0 - 40°C
- Able to be used as a regulated medical device

Physical Specifications:
- Complete unit must include motor, vacuum pump, electronic controls and software
- Electronic controls must include switches to control power on/off, charging, frequency/mode selection & vacuum level
- Complete unit must have dimensions that are compatable with a desktop appliance (approx. 30x15x15cm)
- Complete unit must be less than 0.5 Kg

Intellectual Property:
The ideal response will include patented technology available for licensing.

Technologies meeting most but not all of these criteria will be considered.

BACKGROUND
A number of consumer products contain electric pumps. Unfortunately, the pumps used in most of these products are noisy, irritating and unrealiable. Products containing electric vacuum pumps are especially offensive.
The goal of this request is to find a consumer vacuum pump system that is compact, quiet, reliable and pleasant to use.


NineSigma, Inc. - www.ninesigma.com - Cleveland, USA
Alfred T. Malouf, Ph.D., Program Manager, email: PhD@ninesigma.com, Tel. +1-216-283-3901



spare parts for Siemens elmo-g vacuum blower

Mar. 2010

Siemens Elmo-G 2BH1 600-ac21
nr. e m5 00 0395 001/00
en. 600 34 3
motor ip 54
50hz - 230/400 V- 3.0 kw
60hz - 400 V - 3.45 kw

We need a replacement fan for the motor

NOPP CO - Omar bin Al-Khattab, 11461 Riyadh, Saudi Arabia
Abdullah ABDULLAH, email: a_waw_a@hotmail.com, Tel. +966555223632, Fax +96612651731



info request for HIBON Type AL 20

Feb. 2010


Have a nice day.

Kindly provide technical details / characteristics of the pump Brand HIBON, Type AL 20, serial number 277128.

Thanks in advance

Koidourmazi Vassiliki

ERGOKINISI - 15 MANOUSOGGIANNAKI, 54621 THESSALONIKI, Greece
Vassiliki KOIDOURMAZI, email: ergokinisi@gmail.com, Tel. +2310233004, Fax +2310233004



looking for a small vacuum pump for a pilot unit

Feb. 2010

Bonjour,

Pour le développement d'un nouveau produit, nous recherchons une petite pompe à vide.
Avez vous des modèles d'occasion à nous proposer.

Sincères salutations
Winco technologies - www.winco-tech.com - 8 Rue du Boisillon, ZI des Châtelets, 22950 Tregueux, France
Jean-Yves Kervadec, email: jy.kervadec@winco-tech.com, Tel. 02.96.78.79.80



gebrauchte Vakuumbeschichtungsanlage für Folien

Jan. 2010

wir suchen eine gebrauchte Vakuumbeschichtungsanlage für Folien.
Baujahr der Anlage sollte von 1983-2001 sein.
Gerne auch mit Support für die Inbetriebnahme und Aufstellung in Indien .

Jorge Moreno - Bissenkamp 3, 44135 Dortmund, Germany
email: j.moreno@gmx.de, mobile +49 (0) 160 510 10 10



Ersatzteile für Brey TF 1 Verdichter / Vakuumpumpe

Jan. 2010

Sehr geehrte Damen und Herren,

Für oben genannte Pumpe, verkauft über Linhof-München mit identischer Typenbezeichnung, benötige ich neue Schieber und Dichtungen.
Eine Explosionszeichnung mit Ersatzteilnummern wäre hilfreich.

V.Leinberger - Sachverständiger für Raumbegrünung - www.raumbegrünung.biz - Goldbergstr.25, 55268 Nieder-Olm, Germany
Volker Leinberger, email: Leinberger-Volker@gmx.de





E-Procurement with
vacuum-guide.com


publish an enquiry for a vacuum pump or vacuum components
vacuum this free service helps you to reach the right suppliers.

eine Vakuumpumpe oder Komponenten anfragen
Vakuum erreichen Sie die richtige Lieferanten mit diesem kostenlosen Service.

publier une demande d'offre pour une pompe à vide ou des composants
vide ce service gratuit vous aide à trouver le bon fournisseur.



 new enquiries

 Archive:  2013  12  11  10  09  08  07  06  05  04


site map